 |
|
12-16-2020, 11:57 PM
|
 |
|
|
Join Date: Jan 2008
Location: Calgary Perchdance
Posts: 19,325
|
|
Getting a VIN for a custom on highway vehicle
__________________
Observing the TIGSCJ in the wilds of social media socio-ecological uniformity environments.
|
12-17-2020, 12:14 AM
|
 |
|
|
Join Date: May 2012
Posts: 2,559
|
|
Quote:
Originally Posted by TreeGuy
Dang! This right here has the potential of being one of those very few legendary AO threads...for a GOOD reason! 
Tree
Sent from my iPhone using Tapatalk |
X2! VERY cool.
Are you sure those Dana 60's are gonna hold up? Those are some BIG tires to turn. A good set of Rockwells would be bulletproof but looks like your well on your way with the 60's. Good luck & keep us posted.
|
12-17-2020, 08:46 AM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
As for registering, there are avenues for getting a new vin and registering home-built vehicles. As for insuring, I can’t speak for all carriers but ours will ensure the vehicle. The only sticking point is I may need to get an appraisal before they will ensure it. I don’t know what it will be worth once done but stuff adds up fast.
Quote:
Originally Posted by does it ALL outdoors
X2! VERY cool.
Are you sure those Dana 60's are gonna hold up? Those are some BIG tires to turn. A good set of Rockwells would be bulletproof but looks like your well on your way with the 60's. Good luck & keep us posted.
|
The 60’s should be fine. They are strong for their weight. I’ve narrowed them to 54-1/2” wheel surface to wheel surface from the original 69”. I’m also now shooting for a 3500lb total weight so the buggy will be on the light side.
The rear 60 has a Detroit automatic locker and Yukon 5.29 gears. The original 30 spline 1-1/4” full floater axle shafts have been replaced with custom length Dutchman 35 spline 1-1/2” 300M shafts.
The front 60 has a selectable cable-actuated OX locker and Yukon 5.29 gears. The original 30 spline 1-1/4” inner and outer shafts have been replaced with 35 spline 1-1/2” 300M shafts. It has Yukon drive flanges at the wheels and Reid Racing knuckles. The high-steer arms are custom made and utilize the 5th (extra) mounting hole that the Reid knuckles have over the stock Ford Kingpin knuckle. The arms mount to the top of the knuckle and face rearwards. When the wheels are straight the arms are pointed at the middle of the rear differential, providing the perfect Ackerman steering angle.
As for steering, I just receiver the complete package from PSC. High-flow pump that mounts on the front of the Ecotec and uses the motors serpentine belt, steering (orbital) control valve, remote reservoir, aluminum cooler, and a massive 8” long x 2-3/4” dia double-ended hydraulic Ram. It also came with an upgraded 1-1/2” tie-rod kit with 3/4” heim joints. I also ordered from another company that specializes in Ecotec swaps the aluminum bracket to mount the PSC pump and they also had the billet pump pulley that matches the 5 rib design on the rest of the Ecotec pulleys.
|
12-17-2020, 08:55 AM
|
|
|
|
Join Date: Oct 2007
Location: To Be Determined.
Posts: 2,190
|
|
Quote:
Originally Posted by TreeGuy
Dang! This right here has the potential of being one of those very few legendary AO threads...for a GOOD reason!
Tree
Sent from my iPhone using Tapatalk |
Right up there with the kidnapping baby birds thread! 😇
Last edited by Iron Brew; 12-17-2020 at 09:08 AM.
|
12-17-2020, 09:11 AM
|
 |
|
|
Join Date: Mar 2008
Posts: 2,073
|
|
Quote:
Originally Posted by does it ALL outdoors
Are you sure those Dana 60's are gonna hold up? Those are some BIG tires to turn. A good set of Rockwells would be bulletproof but looks like your well on your way with the 60's. Good luck & keep us posted.
|
Unless he ends up adding TONS of weight, the 60's will be more than enough.
He'll also be saving over a couple hundred pounds not going with Rockwells.
It's looking great Posi. Thanks for the updates.
|
12-17-2020, 09:24 AM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
I think what most people need to remember is that this is a purpose built vehicle. It’s going to spend most of its time going 5km/hr through boggy ground with water coming up through it. There’s hard ground up here too but you seldom go in any direction for long before hitting some Muskeg. If I was building a rock crawler it would look a lot different.
|
12-17-2020, 10:34 AM
|
|
|
|
Join Date: Sep 2012
Posts: 6,439
|
|
Posi, I like your design, most guys do not know the Ft Mc muskeg, only way to cross some is with a pair of chest waders or wait until January when you have a foot of ice.
|
12-17-2020, 10:53 AM
|
|
|
|
Join Date: Mar 2009
Location: Edmonton
Posts: 9,851
|
|
I love the build, can't wait for the videos to follow of it doing it's thing.
|
12-17-2020, 12:26 PM
|
 |
|
|
Join Date: Dec 2008
Location: Alberta
Posts: 24,067
|
|
__________________
Only dead fish go with the flow. The rest use their brains in life.
Originally Posted by Twisted Canuck
I wasn't thinking far enough ahead for an outcome, I was ranting. By definition, a rant doesn't imply much forethought..... 
|
12-17-2020, 02:57 PM
|
 |
Moderator
|
|
Join Date: Jul 2008
Location: A bit North o' Center...
Posts: 11,818
|
|
Quote:
Originally Posted by Ken07AOVette
|
My boys watch this guys' antics all the time.
Oh to have the money to burn on the kinds of stuff he builds and wrecks... I can't bear to watch!
|
12-17-2020, 05:33 PM
|
 |
|
|
Join Date: Jul 2016
Posts: 3,718
|
|
__________________
“One of the sad signs of our times is that we have demonized those who produce, subsidized those who refuse to produce, and canonized those who complain.” - Thomas Sowell
“We seem to be getting closer and closer to a situation where nobody is responsible for what they did but we are all responsible for what somebody else did.”- Thomas Sowell
|
12-17-2020, 05:49 PM
|
|
|
|
Join Date: Jun 2015
Location: Calgary SW
Posts: 311
|
|
People like Positrac are the reason why Albertans overcome problems again and again. I salute you.
|
12-17-2020, 06:00 PM
|
|
|
|
Join Date: Dec 2008
Posts: 803
|
|
What a cool thread. Well done sir! I want a ride. 
|
12-17-2020, 06:52 PM
|
|
|
|
Join Date: Oct 2018
Posts: 7,704
|
|
Definitely need to post a video of it in action when your all done
|
12-17-2020, 07:20 PM
|
|
|
|
Join Date: Nov 2019
Posts: 604
|
|
Great project Posi... a question. Having never been involved in this sort of thing you mentioned a serpentine belt. Do those belts not slip and cause problems when buried in muck and mud?
Osky
|
12-17-2020, 07:44 PM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
Quote:
Originally Posted by Osky
Great project Posi... a question. Having never been involved in this sort of thing you mentioned a serpentine belt. Do those belts not slip and cause problems when buried in muck and mud?
Osky
|
If I quit adding more steel to it the belt will be up high enough that it will be out of the water even when floating.
|
12-18-2020, 10:38 AM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
Motor and transaxle hard mounted. I have a stand-alone harness and new tuned ecu from Swap Specialties that will handle running both.
Hard mount for the Samurai transfer case. I still have a top crossbar to add. Note the transfer case brake. I have a dual piston brake pedal assembly and two separate calibers going on the brake. Everything is above the frame rails and I have a 3-piece skid plate that covers everything. At 3 psi there will be about 22” of clearance under the belly.
|
12-18-2020, 11:28 AM
|
|
|
|
Join Date: Feb 2014
Location: The best place on earth.
Posts: 1,667
|
|
That’s very impressive Posi! Way to grab the bull by the horns and make it happen. I’ll be following this till the end, great work so far.
__________________
Life’s a garden, Dig it! - Joe Dirt
|
12-18-2020, 09:16 PM
|
|
|
|
Join Date: Mar 2008
Location: Alberta
Posts: 4,278
|
|
I may have missed it, but what do you expect the whole thing to weigh?
|
12-18-2020, 09:28 PM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
Quote:
Originally Posted by double gun
I may have missed it, but what do you expect the whole thing to weigh?
|
I started out wanting it to come in at 3,000lbs but it will probably end up around 3,500.
|
12-18-2020, 09:58 PM
|
 |
Moderator
|
|
Join Date: Feb 2015
Posts: 8,099
|
|
Why did you hard mount vs soft mount? Not going fast enough to be concerned with increased harshness?
|
12-18-2020, 10:42 PM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
Quote:
Originally Posted by Trochu
Why did you hard mount vs soft mount? Not going fast enough to be concerned with increased harshness?
|
A lot of buggy’s hard mount the motor/transaxle and a lot of the Samurai crowd do the same with the transfer case. The frame is very ridged so flex shouldn’t be an issue.
|
12-18-2020, 10:50 PM
|
|
|
|
Join Date: May 2012
Posts: 2,559
|
|
Quote:
Originally Posted by Positrac
As for registering, there are avenues for getting a new vin and registering home-built vehicles. As for insuring, I can’t speak for all carriers but ours will ensure the vehicle. The only sticking point is I may need to get an appraisal before they will ensure it. I don’t know what it will be worth once done but stuff adds up fast.
The 60’s should be fine. They are strong for their weight. I’ve narrowed them to 54-1/2” wheel surface to wheel surface from the original 69”. I’m also now shooting for a 3500lb total weight so the buggy will be on the light side.
The rear 60 has a Detroit automatic locker and Yukon 5.29 gears. The original 30 spline 1-1/4” full floater axle shafts have been replaced with custom length Dutchman 35 spline 1-1/2” 300M shafts.
The front 60 has a selectable cable-actuated OX locker and Yukon 5.29 gears. The original 30 spline 1-1/4” inner and outer shafts have been replaced with 35 spline 1-1/2” 300M shafts. It has Yukon drive flanges at the wheels and Reid Racing knuckles. The high-steer arms are custom made and utilize the 5th (extra) mounting hole that the Reid knuckles have over the stock Ford Kingpin knuckle. The arms mount to the top of the knuckle and face rearwards. When the wheels are straight the arms are pointed at the middle of the rear differential, providing the perfect Ackerman steering angle.
As for steering, I just receiver the complete package from PSC. High-flow pump that mounts on the front of the Ecotec and uses the motors serpentine belt, steering (orbital) control valve, remote reservoir, aluminum cooler, and a massive 8” long x 2-3/4” dia double-ended hydraulic Ram. It also came with an upgraded 1-1/2” tie-rod kit with 3/4” heim joints. I also ordered from another company that specializes in Ecotec swaps the aluminum bracket to mount the PSC pump and they also had the billet pump pulley that matches the 5 rib design on the rest of the Ecotec pulleys.
|
Roger that, I just read it's going to be a light buggy, those 60's (built) will be more than strong enough. I was assuming it would be a hardcore bush buggy.
Again, very cool project!
Looks like your making KILLER progress. Also looks like you have some serious fab skills.
|
12-18-2020, 11:37 PM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
Quote:
Originally Posted by does it ALL outdoors
Looks like your making KILLER progress. Also looks like you have some serious fab skills.
|
Thanks. I played with Lego lots as a kid.
I’ve got a long ways to go before I can pat myself on the back. Maybe next fall when I’ve got a bull loaded up on it heading out of the bush...
|
12-19-2020, 05:22 PM
|
|
|
|
Join Date: Mar 2008
Location: Alberta
Posts: 4,278
|
|
Yeah this is damn impressive, and I appreciate you letting us come along for the build.
|
12-19-2020, 09:18 PM
|
|
Moderator
|
|
Join Date: Aug 2012
Location: Wheatland County
Posts: 5,888
|
|
Cool project for sure. You putting a winch on it or some type of tire chain possible ?
|
12-19-2020, 09:38 PM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
I’ve got winches for both front and rear of the buggy. They are only 4,000lb units but I’ve got a few snatch blocks and extra winch rope so they should be sufficient.
Today was spent on the end of the welder whip. Oh, and a bit of time just spent staring at it...lol.
I mentioned the 3-piece skid plates in a previous post. Here is a couple pics of them a few months back when I had the frame flipped over.
|
12-19-2020, 09:57 PM
|
|
Moderator
|
|
Join Date: Feb 2015
Posts: 8,099
|
|
It's weird seeing the axles welded to the frame.
Makes it alot easier to build though.
|
12-19-2020, 11:09 PM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
Quote:
Originally Posted by Trochu
It's weird seeing the axles welded to the frame.
Makes it alot easier to build though.
|
Cuts down on axle wrap too....
|
12-22-2020, 06:38 PM
|
|
|
|
Join Date: Apr 2013
Posts: 3,281
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 02:41 AM.
|
Linear Mode
